ADTRAN Stub Routing Instrukcja Użytkownika Pobierz pdf

Lab 4.9.1 Configuring ISDN BRI

Objective

In this lab, the student will configure two Cisco routers for DDR using ISDN BRI. The student will also

configure PPP CHAP authentication.

Scenario

The International Travel Agency (ITA) wants an ISDN DDR connection configured between a remote

office in Capetown and its corporate office known as SanJose1. For security reasons, and to keep

ISDN charges to a minimum, suggest that only Web, e-mail, FTP, Telnet, and DNS traffic activate

the link from the remote site. Also recommend configuring PPP CHAP authentication. Finally,

Capetown connects to a stub network. For this reason, suggest that static and default routes be used

between both sites.

Step 1

Before beginning this lab, it is recommended that the routers be reloaded after erasing their startup

configuration. This will prevent problems that may be caused by residual configurations.

Build and configure the network according to the diagram, but do not configure the BRI interfaces for

either router yet. Use the Adtran Atlas 550 or similar device to simulate the ISDN cloud. If the Atlas

550 is used, be sure to use straight-through cables. Connect both routers to the respective BRI

module ports of the Atlas 550 as labeled in the diagram.

Configure the hostname and FastEthernet 0/0 interfaces on each router.

Configure both workstations with their respective IP addresses and default gateways. For example,

the router Fa0/0 IP address. Have each host ping their default gateway to verify connectivity.

1 - 7 CCNP 2: Remote Access v 3.0 - Lab 4.9.1 Copyright  2003, Cisco Systems, Inc.

1 2 3 4 5 6 7

Objective 1
Scenario 1

Podsumowanie treści

Strona 1 - Scenario

Lab 4.9.1 Configuring ISDN BRI Objective In this lab, the student will configure two Cisco routers for DDR using ISDN BRI. The student will also co

Strona 2

Step 2 In global configuration mode on SanJose1, use the following to configure the username and password information for the remote router and an ena

Strona 3

Sa nJose1(config-if)#dialer idle-timeout 60 Next, configure the DDR setting on the BRI interface. Use the dialer-group 1 command as follows, to asso

Strona 4

The debug isdn q921 command may also be used to troubleshoot Layer 2 issues between the router and the ISDN switch. Once connectivity to the ISDN sw

Strona 5

Idle timer (120 secs), Fast idle timer (20 secs) Wait for carrier (30 secs), Re-enable (15 secs) Dialer state is idle 4. What is the idle timer set

Strona 6

Finally, because PPP with CHAP authentication is being used, also debug PPP as follows: SanJose1#debug ppp authentication SanJose1#debug ppp negotiat

Strona 7

Out 5551000 SanJose1 18 44 15 0 ---------------------------------------------------------------------

Więcej dokumentów dla Networking ADTRAN Stub Routing

Aby wyświetlić dokument ADTRAN Stub Routing Instrukcja Użytkownika

ADTRAN Stub Routing Instrukcja Użytkownika (18 strony)

Aby wyświetlić dokument ADTRAN Stub Routing Dokumentacja

ADTRAN Stub Routing Dokumentacja (568 strony)

Aby wyświetlić dokument ADTRAN Stub Routing Podręcznik Użytkownika

ADTRAN Stub Routing Podręcznik Użytkownika (132 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

ADTRAN Stub Routing Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Networking ADTRAN Stub Routing. Lab 4.9.1 Configuring ISDN BRI Instrukcja obsługi

Podsumowanie treści

Więcej dokumentów dla Networking ADTRAN Stub Routing

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Networking ADTRAN Stub Routing